Contrastive analysis of cooling performance between a high-level water collecting cooling tower and a typical cooling tower

A three-dimensional (3D) numerical model is established and validated for cooling performance optimization between a high-level water collecting natural draft wet cooling tower (HNDWCT) and a usual natural draft wet cooling tower (UNDWCT) under the actual operation condition at Wanzhou power plant, Chongqing, China. User defined functions (UDFs) of source terms are composed and loaded into the spray, fill and rain zones. Considering the conditions of impact on three kinds of corrugated fills (Double-oblique wave, Two-way wave and S wave) and four kinds of fill height (1.25 m, 1.5 m, 1.75 m and 2 m), numerical simulation of cooling performance are analysed. The results demonstrate that the S wave has the highest cooling efficiency in three fills for both towers, indicating that fill characteristics are crucial to cooling performance. Moreover, the cooling performance of the HNDWCT is far superior to that of the UNDWCT with fill height increases of 1.75 m and above, because the air mass flow rate in the fill zone of the HNDWCT improves more than that in the UNDWCT, as a result of the rain zone resistance declining sharply for the HNDWCT. In addition, the mass and heat transfer capacity of the HNDWCT is better in the tower centre zone than in the outer zone near the tower wall under a uniform fill layout. This behaviour is inverted for the UNDWCT, perhaps because the high-level collection devices play the role of flow guiding in the inner zone. Therefore, when non-uniform fill layout optimization is applied to the HNDWCT, the inner zone increases in height from 1.75 m to 2 m, the outer zone reduces in height from 1.75 m to 1.5 m, and the outlet water temperature declines approximately 0.4 K compared to that of the uniform layout.     

Finite Element Study on the Influence of Structural Parameters on the Ballistic Performance of 3D Networked Fabrics

Networked fabrics are a type of three-dimensional multilayer fabrics having predetermined interconnections between layers by combining yarns from two adjacent sublayers into one. This paper reports the research on the influence of structural parameters on the ballistic performance of networked fabrics using finite element analysis in parallel with experiment. The widths of separate and combined sections are found to affect the energy absorption (EA) of regular networked fabrics against high-velocity impact. Separate sections of networked fabrics generally outperform combined sections. The optimal width of the separate section is around 9.5 cm for both dense and loose networked fabrics when impacted at the separate section. The optimal width of combined section decreases from 2.38 cm to 1.15 cm with the decrease of weave density in this area. For the studied structural parameters, highest EAs of dense and loose networked fabrics are around 13.3% and 17.1% higher than those of their counterpart layups of dense and loose plain-woven fabrics, respectively. These findings suggest networked fabrics could be engineered to improve the ballistic performance of flexible fabrics.     

Improving the physical and mechanical properties of particleboards made from urea–glyoxal resin by addition of pMDI

The effect of pMDI on physical and mechanical properties of the particleboards made from urea–glyoxal resin was investigated. The nontoxic and ecofriendly urea–glyoxal (UG) resin was synthesized under weak acid conditions, and its different properties were measured. Then, pMDI at various contents (4, 6 and 8% on resin solids) was added to the UG resin prepared. The thermal and physicochemical properties of the resins prepared as well as their water absorption, flexural properties (flexural modulus and strength) and internal bond (IB) strength of the particleboard panels bonded with them were measured according to standard methods. According to the physicochemical results obtained, the addition of pMDI significantly accelerated the gel time and increased the viscosity and solids content of UG resins. Differential scanning calorimetry indicated that the addition of pMDI decreases the onset and curing temperatures of the UG resin. Physical analysis results of the panels indicated that the particleboards made from UG resins with isocyanate yielded lower water absorption when compared to those bonded with the control UG resins. Based on the findings of this research work, the mechanical properties of particleboard panels bonded with UG resins could be significantly enhanced by the addition of increasing percentages of pMDI. The panels having 8 wt% pMDI exhibited the highest flexural modulus, flexural strength and IB strength value and the lowest water absorption among all the panels prepared.     

Optimal sensor placement for joint parameter and state estimation problems in large-scale dynamical systems with applications to thermo-mechanics

We consider large-scale dynamical systems in which both the initial state and some parameters are unknown. These unknown quantities must be estimated from partial state observations over a time window. A data assimilation framework is applied for this purpose. Specifically, we focus on large-scale linear systems with multiplicative parameter-state coupling as they arise in the discretization of parametric linear time-dependent partial differential equations. Another feature of our work is the presence of a quantity of interest different from the unknown parameters, which is to be estimated based on the available data. In this setting, we employ a simplicial decomposition algorithm for an optimal sensor placement and set forth formulae for the efficient evaluation of all required quantities. As a guiding example, we consider a thermo-mechanical PDE system with the temperature constituting the system state and the induced displacement at a certain reference point as the quantity of interest.     

A comparison study of Taiwanese He-Yuan Architecture between the ethically spatial order and the condition of physical environment

Since the 21st century, problems such as global warming and energy depletion have become important issues to scientists and architects. The architectural design nowadays often relies on large amount of mechanical equipment to create a comfortable environment for the users. However, it burdens and deteriorates the nature. On the other hand, some of the traditional architecture in the past can cope with the local humid and hot climate, achieving good passive heat control for the environment. Therefore, this study explores the relation between traditional residents in Taiwan’s use of space and the external environment and climate through modern environment measurement technique, restores and conducts quantitative analysis on the interior thermal environment and light environment of Lin-An-Tai Historical House in the past through Ecotect Analysis, and analyzes the results of the calculation in terms of its spatial allocation, openings, and outer walls, etc. This study also evaluates the effects of lighting and user’s sense of comfortable temperature under its environmental conditions according to the standards of residential quality nowadays. It further studies the ancestor of traditional architecture by reviewing its spatial order and compares to the current situation in order to feedback the modern architecture design. Part of the results of the simulation show that the variation of temperature indoors in each space is less dynamic than that of outdoors. The temperature in the space at the right of the main hall (northwestern side) is generally higher than that in the left (southeastern side). The highest temperature in the space farther away from the interior patio is usually higher than that in the space closer to the interior patio. The temperature near the outer side of the space above Hulong is higher than that in the middle. Accordingly, the location is closely related to the interior temperature. As to human’s sense of comfortable temperature, the results show that in summer, the Predicted Mean Vote (PMV) in the space at the left of the main hall (southeastern side) is generally higher than that in the right (northwestern side). In winter, the sense of comfortable temperature in the rooms in the corner is lower than that in other rooms at the inner side, the comparison between the space ethical order and the evaluation result did not show any obvious relationship. For the evaluation of lighting, the main hall and the restaurant at the outer left Hulong have better lighting while other space does not have sufficient and even lighting. Artificial lighting is needed to make the space more functional, the results shows that lighting conditions of space did not metaphor to the space ethical order.     

An experimental investigation on slope stability under drawdown conditions using transparent soils

This paper presents an experimental investigation into slope failure during water-level drawdown using transparent soil. The internal characteristics of slope failure are not well-known due to the limitations of the techniques used in the experiments conducted to date. In this study, transparent soil is used to visualize the process of slope failure. We developed a water-level control system to implement simulation of the drawdown of the water level at various speeds and used a charge-coupled device camera to capture images during the entire slope failure process. Particle image velocimetry was used to measure the displacement of the sand particles and identify the sliding zones. The flow paths of the fluid inside the slope were illuminated using an organic dye. The results show that the slope failure process can be divided into two stages: surface and overall sliding. The overall sliding of the slope is caused by the gradual development of partial instability, and the failure mode is a cyclic failure. The slope angle is different above and below the water level during the process of sliding. In our experiments, the slope angle is about 20° above the water level, which is the same as the final stable slope angle, and about 35° below the water level, which is the same as the initial slope angle. This means that the drawdown influences the angle above the water level but has little influence on the angle below the water level. The results of this paper provide a better understanding of the physical behavior and failure mode of soil slopes caused by drawdowns near the coast.     

A Novel Approach for Bolted T-Stub Connections

This paper reports an investigation into new connection types and their behaviors determined using full-scale experiments. T-shaped connections were created using the IPE standard profile. The aim of this study was to analyze the influence of T connections based on the IPE standard profile, height of beam to height of T-stub joint (H) of T-stub joints, and lengths (X) of T-stub joints on the behavior of steel connections, in order to provide the necessary data for improving Eurocode 3 and enable efficient use of residue IPE standard profiles and back to the consumption cycle. While the moment resistance values increased with an increase in H from H_min to H_max in model groups with X of 126 mm, and the energy dissipation increased with an increase in H from H_min to H_max and also with an increase in the lengths (X) of T-stub joints from 54 to 126 mm.     

济阳坳陷下古生界潜山油气藏特征及成藏模式

济阳坳陷下古生界潜山具有多样性、复杂性的特点，潜山差异性的形成演化、油气成藏主控因素和控藏模式不明确，严重制约了该区潜山油气勘探。在潜山分类的基础上，综合利用系统恢复、分类对比和典型解剖等方法，揭示了济阳坳陷下古生界不同类型潜山的形成演化过程和油气成藏主控因素差异性，分类建立了油气成藏模式。研究表明，济阳坳陷下古生界主要发育高位新盖侵蚀残丘潜山、中位古盖拉张断块潜山、中位新古盖拉张剪切断块潜山、中位中古盖挤压拉张断块潜山和低位古盖拉张滑脱断块潜山5种潜山类型。不同类型潜山的形成演化和油气成藏各具特色，其中，高位新盖侵蚀残丘潜山的发育受隆升、侵蚀作用控制，油气成藏主要受控于油源和盖层条件，表现为"单向供烃、砂体-不整合岩溶体联合输导、残丘控藏"的成藏模式；中位古盖拉张断块潜山的发育受掀斜、断裂作用控制，油气成藏主要受控于储集条件，表现为"单向供烃、顺向断层输导、反向断层控藏"的成藏模式；中位新古盖拉张剪切断块潜山的发育受反转、翘倾和走滑切割作用控制，油气成藏主要受控于输导条件，表现为"多源供烃、断溶体立体输导、断裂控藏"的成藏模式；中位中古盖挤压拉张断块潜山的形成受强烈挤压、拉张滑脱作用控制，油气成藏主要受控于储集条件，表现为"多源供烃、断缝体输导、断褶控藏"的成藏模式；低位古盖拉张滑脱断块潜山的形成受强烈拉张滑脱作用控制，油气成藏主要受控于输导条件，表现为"顶部供烃、断缝体输导、断裂控藏"的成藏模式。     

Microwave dielectric properties of SrLa[Ga1−x(Mg0.5Ti0.5)x]O4 and SrLa[Ga1−x(Zn0.5Ti0.5)x]O4 (x = 0.2-0.8) ceramics

SrLa[Ga_1−x(R_0.5Ti_0.5)_x]O₄ (R = Mg, Zn) ceramics were prepared by a standard solid state sintering method. The single-phase ceramics with K₂NiF₄-type layered perovskite structure and I4/mmm space group were obtained, indicating that SrLa(R_0.5Ti_0.5) and SrLaGaO₄ can form the unlimited solid solutions. With increasing x for R = Mg and Zn, ε_r increases monotonously, the Qf value first increases and then decreases, while τ_f increases from a negative to a positive value. The optimized microwave dielectric properties were obtained as following: ε_r = 23.3, Qf = 89 400 GHz, τ_f = −0.8 ppm/°C for SrLa[Ga_0.6(Mg_0.5Ti_0.5)_0.4]O₄ and ε_r = 23.3, Qf = 76 200 GHz, τ_f = 0.2 ppm/°C for SrLa[Ga_0.7(Zn_0.5Ti_0.5)_0.3]O₄, indicating that the present solid solution ceramics are the promising candidates as microwave resonator materials for the telecommunication applications.